A strong flush mount cup holder fits the cutout, holds the containers you use, and suits the moisture and space demands of its installation—whether that is a boat, RV, vehicle, sofa, or table. The Sea-Dog 588060 Combo Drink Holder leads this selection with a dual-purpose design for cans with or without insulated wraps and a stated 3-3/4-inch hole requirement. Other options trade that can-wrap flexibility for stainless-steel construction, included drainage parts, a smaller 3-inch installation hole, or multipacks for several locations.
Before choosing, compare the required opening with your panel, then check the holder’s inside diameter and depth against your drinkware. Product listings do not provide a complete fit specification for every model, so verify dimensions before cutting or ordering.
The Sea-Dog 588060 Combo Drink Holder is the best overall choice in this group for buyers seeking a flush-mounted holder that accommodates cans with or without insulated can wraps. It is injection-molded ABS, has a stated 3-5/8-inch inside diameter and 3-1/4-inch depth, and requires a 3-3/4-inch hole. If you need a smaller installation opening, the Sea-Dog 588000 Flush Drink Holder requires a 3-inch hole, while the Whitecap S-3511C Stainless Drink Holder includes a gasket, pad, and drain tube.
Our Top Picks

Sea-Dog 588060 Combo Drink Holder
Its 3-5/8-inch inside diameter and 3-1/4-inch depth suit cans with or without insulated wraps; it requires a 3-3/4-inch hole.
View on Amazon
Best Stainless SteelWhitecap S-3511C Stainless Drink Holder
Stainless steel, a 3-7/8-inch cutout, and included mounting gasket, pad, and drain tube make this a well-specified marine flush-mount option.
View on Amazon
Smallest CutoutSea-Dog 588000 Flush Drink Holder
The listed 3-inch installation hole is smaller than the openings specified for several alternatives; its ABS holder accommodates containers up to 2-7/8 inches wide.
View on Amazon- Closeable Drain MARINE CITY Closeable Drain Holder
- Multipack Pick Amarine Made Recessed Holder
Compare Flush-Mount Cup Holder Features
| # | Product | Dimensions | Weight | Material | Buy |
|---|---|---|---|---|---|
| 1 | 1. Sea-Dog 588060 Combo Drink HolderBest Overall | — | 1.92 oz | Acrylonitrile Butadiene Styrene | View on Amazon |
| 2 | 2. Whitecap S-3511C Stainless Drink HolderBest Stainless Steel | 2.5"L x 2.5"W x 3.25"H | 4.8 oz | Stainless Steel | View on Amazon |
| 3 | 3. Sea-Dog 588000 Flush Drink HolderSmallest Cutout | 3.19"L x 0.75"W x 1"H | 22.68 g | Acrylonitrile Butadiene Styrene | View on Amazon |
| 4 | 4. MARINE CITY Closeable Drain HolderCloseable Drain | 3.36"L x 3.36"W x 0.59"H | — | Plastic | View on Amazon |
| 5 | 5. Amarine Made Recessed HolderMultipack Pick | 4.13"L x 4.13"W x 3.5"H | 0.01 kg | Plastic | View on Amazon |
| 6 | 6. FR Flush Mount Cup HolderIndoor-outdoor replacement | — | 2.56 oz | Plastic | View on Amazon |
| 7 | 7. SDTC Tech Sofa Cup HolderWide sofa-seat openings | 4.36"L x 3.5"W x 2.5"H | — | Plastic | View on Amazon |
| 8 | 8. Whitecap S-3511BC LED HolderBlue-light drink station | 4"L x 4"W x 2.5"H | 5.6 oz | Plastic | View on Amazon |
| 9 | 9. BETIMFAN Stainless Drop-In HolderTwo-piece stainless set | 4.13"L x 4.13"W x 3.43"H | — | Stainless Steel | View on Amazon |
| 10 | 10. harayaa Flush Mount InsertGlossy recessed panels | 4.33"L x 4.33"W x 2.17"H | — | — | View on Amazon |
Detailed Reviews: Best Flush Mount Cup Holder

#1 · Best Overall
1. Sea-Dog 588060 Combo Drink Holder
- Weight: 1.92 oz
- Material: Acrylonitrile Butadiene Styrene
Best for: Insulated-can flexibility.
Why it ranks #1: Its 3-5/8-inch inside diameter and 3-1/4-inch depth suit cans with or without insulated wraps; it requires a 3-3/4-inch hole.
A dual-purpose 3-5/8-inch interior accepts beverage cans with or without insulated can wraps, so the same recessed holder can handle both bare and covered cans. Its injection-molded ABS body includes drain holes, while the required 3-3/4-inch hole gives the installation a defined opening size.
The dual-purpose design addresses a common change in drinkware: use a can directly or leave its insulated wrap on without switching holders. A 3-5/8-inch inside diameter provides the stated opening, and the 3-1/4-inch depth gives the cup a recessed place to sit. Injection-molded ABS keeps the construction plastic, while bottom drain holes provide a route for moisture. Before installation, plan for the specified 3-3/4-inch hole in the mounting surface.
- Fits cans with or without insulated wraps
- 3-5/8-inch inside diameter
- 3-1/4-inch depth
- Injection-molded ABS with drain holes
- Its 3-3/4-inch hole requirement exceeds the 3-inch opening specified for the Sea-Dog 588000.
Skip it if you are limited to a 3-inch cutout; the Sea-Dog 588000 is specified for that smaller hole.
Pick this Sea-Dog for boat or vehicle drink stations where cans may be used bare or with insulated wraps. Its 3-3/4-inch required opening is the key boundary, so verify the panel space before installation.
Full product details
| Brand | Sea-Dog |
|---|---|
| Color | Black |
| Included Components | Sea-Dog 588060 Flush Mount Combo Drink Holder With Drain Holes – Black |
| Item Weight | 1.92 ounces |
| Manufacturer | Sea-Dog |
| Part Number | 588060 |
| Material | Acrylonitrile Butadiene Styrene |
| Model Number | 588060 |
Listed on Amazon as: Sea-Dog 588060 Flush Mount Combo Drink Holder with Drain Holes – Black, 3-5/8" ID x 3-1/4" D
View on Amazon
#2 · Best Stainless Steel
2. Whitecap S-3511C Stainless Drink Holder
- Dimensions: 2.5"L x 2.5"W x 3.25"H
- Weight: 4.8 oz
- Material: Stainless Steel
Best for: Polished stainless marine fit.
Why it ranks #2: Stainless steel, a 3-7/8-inch cutout, and included mounting gasket, pad, and drain tube make this a well-specified marine flush-mount option.
A polished stainless-steel body resists wear while retaining its high-polished look, offering a durable alternative to plastic for a recessed drink station. Its 3-7/8-inch cutout and 2-1/4-to-3-1/8-inch depth range give buyers concrete installation dimensions, and the included gasket, pad, and drain tube support the mounting setup.
The stainless-steel construction is described as more durable than plastic and able to withstand wear without losing its polished appearance, an advantage where the holder remains visible. It fits cans, bottles, and can coolers, covering common drink formats without limiting use to bare cans. Installation calls for a 3-7/8-inch cutout; the 4-1/4-inch outside diameter frames that opening, while the variable 2-1/4-to-3-1/8-inch depth and included gasket, pad, and drain tube inform the fitting process.
- Stainless-steel construction with polished appearance
- Fits cans, bottles, and can coolers
- Specified 3-7/8-inch cutout
- Includes mounting gasket, pad, and drain tube
- The specified cutout is 3-7/8 inches, larger than the 3-inch Sea-Dog 588000 requires.
Skip it if you have only a 3-inch opening available; the Sea-Dog 588000 calls for that smaller cutout.
This Whitecap is suited to buyers prioritizing polished stainless steel and compatibility with cans, bottles, and can coolers. Its installation requires a 3-7/8-inch cutout, so it is not a match for smaller existing openings.
Full product details
| Brand | Whitecap |
|---|---|
| Color | Beige |
| Included Components | Whitecap S-3511C Stainless Steel Flush Drink Holder – 3-7/8" Cutout, 2-1/4" to 3-1/8" Depth |
| Dimensions | 2.5"L x 2.5"W x 3.25"H |
| Item Weight | 4.8 ounces |
| Manufacturer | Whitecap |
| Part Number | S-3511C |
| Material | Stainless Steel |
| Model Number | S-3511C |
Listed on Amazon as: Whitecap Industries S-3511C Stainless Steel Flush Drink Holder – 3-7/8" Cutout, 2-1/4" to 3-1/8" Depth
View on Amazon
#3 · Smallest Cutout
3. Sea-Dog 588000 Flush Drink Holder
- Dimensions: 3.19"L x 0.75"W x 1"H
- Weight: 22.68 g
- Material: Acrylonitrile Butadiene Styrene
Best for: Compact marine installations.
Why it ranks #3: The listed 3-inch installation hole is smaller than the openings specified for several alternatives; its ABS holder accommodates containers up to 2-7/8 inches wide.
A 2-inch-deep ABS cup holder keeps its profile shallow while accepting drink containers up to 2-7/8 inches in diameter. Its flush-mount format suits installations where a recessed holder is preferred, and the specified 3-inch hole gives installers a clear cutout target before work begins.
The injection-molded ABS construction provides a plastic holder for marine or other suitable installations, while the 2-inch depth limits how far the cup occupies space below the mounting surface. Its stated capacity for containers up to 2-7/8 inches wide helps buyers assess drink compatibility, and the required 3-inch-diameter hole makes the panel preparation requirement explicit. Choose this model when a shallow holder and defined cutout matter more than a deeper cup well.
- Injection-molded ABS construction
- 2-inch holder depth
- Accommodates containers up to 2-7/8 inches in diameter
- Requires a specified 3-inch hole
- Its 2-inch depth is shallower than the listed 3-inch Sea-Dog combo holder.
Skip it if you need room for insulated can wraps; the Sea-Dog 588060 combo holder accommodates cans with or without them.
This Sea-Dog suits boat owners or other installers seeking a shallow, black flush-mount holder for containers no wider than 2-7/8 inches. Account for its 3-inch cutout and 2-inch depth before choosing it.
Full product details
| Brand | Sea-Dog |
|---|---|
| Color | Black |
| Included Components | Sea-Dog 588000 Flush Mount Drink Holder, 2" Deep – Black |
| Dimensions | 3.19"L x 0.75"W x 1"H |
| Item Weight | 22.68 g |
| Manufacturer | Sea-Dog |
| Part Number | 588000 |
| Manufacturer Warranty Description | See Manufacturer |
| Material | Acrylonitrile Butadiene Styrene |
| Model Number | 588000 |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: Sea-Dog 588000 Flush Mount Drink Holder, 2" Deep – Black
View on Amazon
#4 · Closeable Drain
4. MARINE CITY Closeable Drain Holder
- Dimensions: 3.36"L x 3.36"W x 0.59"H
- Material: Plastic
Best for: Flexible cup-size fit.
Why it ranks #4: Its polypropylene flush-mount design has a drain that can be closed and sealed with the supplied nut and bolt, plus a stepped cup opening.
A stepped interior accommodates standard-size containers as well as larger cups or cans wearing cozies, making this closeable-drain holder adaptable to mixed drinkware. The flush-mount polypropylene design is specified for boats, vehicles, and indoor settings, while its drain plug can be closed and sealed with the supplied nut and bolt.
The stepped shape gives standard containers and wider insulated cans different seating positions, so one holder can serve changing drink choices. Its drain includes a nut and bolt that close and seal the opening, offering control over whether liquid can pass through during use. Polypropylene construction and flush mounting suit a range of listed settings, including boats, cars, RVs, and sofas. The product dimensions are 3.36 inches by 3.36 inches by 0.59 inches; plan the mounting surface around the intended installation.
- Stepped design accommodates standard and larger containers
- Drain can be closed and sealed with a nut and bolt
- Polypropylene plastic construction
- Listed for boats, cars, RVs, and other settings
- The listed dimensions do not specify a required mounting-hole diameter.
Skip it if you want a stated cutout size and stainless construction; the Whitecap S-3511C specifies a 3-7/8-inch cutout.
Choose this MARINE CITY holder for mixed-size drinkware across boat, vehicle, or indoor installations, especially when a sealable drain is useful. Its listing does not provide a mounting-hole diameter, so that detail remains unresolved.
Full product details
| Brand | MARINE CITY |
|---|---|
| Capacity | 1.9 pounds |
| Color | Black |
| Included Components | Barb |
| Dimensions | 3.36"L x 3.36"W x 0.59"H |
| Manufacturer | MARINE CITY |
| Part Number | MC32761628-1 |
| Material | Plastic |
| Model Number | MC32761628-1 |
Listed on Amazon as: MARINE CITY Closeable Plastic Cup Holder with Drain Black Durable Flush Mount Design for Boats RVs Cars Ships Marines Yachts & Kayaks (Pack of 1)
View on Amazon
#5 · Multipack Pick
5. Amarine Made Recessed Holder
- Dimensions: 4.13"L x 4.13"W x 3.5"H
- Weight: 0.01 kg
- Material: Plastic
Best for: Three-holder marine setups.
Why it ranks #5: The set includes three recessed plastic holders with drain holes, a 3-1/2-inch inside diameter, and a 4-1/8-inch outside diameter.
A set of three recessed plastic holders lets buyers equip several positions with matching drink spaces, each with bottom drain holes to keep moisture away. The 3-1/2-inch inside diameter fits a range of cans and drinks, while the smooth finish is stated to make cleanup easy.
The three-piece set can supply multiple locations, and each holder’s 3-1/2-inch inside diameter offers a defined opening for drinkware. Drain holes in the bottom provide a path for moisture, useful in the listed boat, car, marine, RV, table, counter, dashboard, and seatback settings. The smooth plastic finish supports easy cleanup. The 3-1/2-inch height and 4-1/8-inch outside diameter help buyers plan the recessed installation, and no mounting screws are required.
- Set includes three holders
- Bottom drain holes help keep moisture away
- 3-1/2-inch inside diameter
- Smooth finish and no mounting screws required
- Its 3-1/2-inch height needs more below-surface room than the 2-inch Sea-Dog 588000.
Skip it if you have limited below-panel depth; the Sea-Dog 588000 is listed at 2 inches deep.
Choose this Amarine Made set for boat, car, RV, or furniture projects needing three matching recessed holders with drain holes. Allow for the listed 3-1/2-inch height and 4-1/8-inch outside diameter.
Full product details
| Brand | Amarine Made |
|---|---|
| Color | Black |
| Dimensions | 4.13"L x 4.13"W x 3.5"H |
| Item Weight | 0.01 kg |
| Manufacturer | Amarine-made |
| Part Number | 3cupholders-Black |
| Material | Plastic |
| Model Number | 3cupholders-Black |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: (Set of 3) Amarine-Made Black Recessed Plastic Cup Drink Can Holder with Drain for Boat Car Marine Rv – Black
View on AmazonWhy it ranks #6: This indoor-or-outdoor plastic replacement measures 3-3/8 inches tall and has a 3-1/2-inch inside diameter for cans, bottles, and glasses.
A two-tiered interior holds cans and bottles in a 3-3/8-inch-tall recessed form, making this plastic holder a replacement option for many brands. The listing names indoor and outdoor use, including tables, chairs, outdoor seating, and private theaters, while its 4-1/3-inch outside diameter sets a useful sizing reference.
The two-tiered shape is stated to hold both bottles and cans, supporting mixed drink choices in a shared seating area. Its 3-1/2-inch inside diameter and 4-1/3-inch outside diameter help distinguish the drink space from the overall rim, while the 3-3/8-inch height indicates the depth below the surface. The product is intended for inset installation and described as a replacement cup for many brands. Plastic construction and indoor/outdoor suitability cover varied seating and table applications.
- Two-tiered design holds cans and bottles
- 3-1/2-inch inside diameter
- Listed for indoor and outdoor installation
- Replacement cup for many brands
- Its 3-3/8-inch height requires more below-surface depth than the 2-inch Sea-Dog 588000.
Skip it if you have limited space below the panel; the Sea-Dog 588000 has a listed 2-inch holder depth.
This FR replacement suits buyers outfitting tables, chairs, outdoor seating, or private theaters with a recessed holder for cans and bottles. Its 3-3/8-inch height makes below-surface clearance an important installation consideration.
Full product details
| Brand | FR |
|---|---|
| Color | Black |
| Item Weight | 2.56 ounces |
| Manufacturer | DSB Global Inc |
| Part Number | CUP066 |
| Material | Plastic |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: This product can expose you to chemicals including bisphenol A (BPA) which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov/furniture |
Listed on Amazon as: FR 3 3/8' x 3 1/2" Outdoor/Indoor Flush Mount Cup Holder
View on Amazon
#7
7. SDTC Tech Sofa Cup Holder
- Dimensions: 4.36"L x 3.5"W x 2.5"H
- Material: Plastic
Best for: Wide sofa-seat openings.
Why it ranks #7: Its ABS insert is 2.5 inches deep, fits a 3.5-inch mounting hole, and accepts beverages up to 3.36 inches in diameter.
A 3.36-inch inside diameter accepts beverages up to that width, giving this ABS recessed holder a broad opening for sofa or furniture use. Its 2.5-inch depth and 3.5-inch mounting-hole diameter establish key fit dimensions, while the smooth, easy-clean surface supports routine cleanup after spills.
The holder’s stated beverage limit is 3.36 inches in diameter, so buyers can compare their cups against a defined maximum. A 3.5-inch mounting hole and 4.36-inch lip diameter distinguish the panel opening from the visible rim, helping plan a recessed installation. ABS plastic and a smooth surface are described as easy to clean, useful in sofa settings where drink spills may occur. The 2.5-inch depth indicates the space needed below the mounting surface.
- Fits beverages up to 3.36 inches in diameter
- Specified 3.5-inch mounting hole
- Smooth ABS surface described as easy to clean
- 2.5-inch depth and 4.36-inch lip diameter listed
- Its 3.5-inch mounting-hole requirement is larger than the 3-inch opening for the Sea-Dog 588000.
Skip it if you have a 3-inch opening and do not want to enlarge it; the Sea-Dog 588000 uses that cutout size.
Choose the SDTC Tech holder for a sofa or recessed setting when a 3.36-inch drink opening and easy-clean ABS surface suit your needs. Its 3.5-inch mounting hole and 2.5-inch depth set the fit limits.
Full product details
| Brand | SDTC Tech |
|---|---|
| Color | Black |
| Included Components | Black Sofa Cup Holder – 2pc |
| Dimensions | 4.36"L x 3.5"W x 2.5"H |
| Manufacturer | SDTC Tech |
| Part Number | CUP-HOLDER-INSERT-3.34 |
| Manufacturer Warranty Description | 30days |
| Material | Plastic |
| Model Number | CUP-HOLDER-INSERT-3.34 |
Listed on Amazon as: SDTC Tech Black Sofa Cup Holder, Universal Plastic Recessed Cup Holder
View on Amazon
#8
8. Whitecap S-3511BC LED Holder
- Dimensions: 4"L x 4"W x 2.5"H
- Weight: 5.6 oz
- Material: Plastic
Best for: Blue-light drink station.
Why it ranks #8: This listing identifies a stainless flush-mount cup holder with a blue LED, but supplies no cutout or depth details to confirm installation fit.
A blue LED light is the named feature that distinguishes this Whitecap flush-mount cup holder, giving buyers a drink station with an illuminated element. The title identifies a stainless-steel finish, but the specifications list plastic as the material; that discrepancy matters when choosing a holder for a particular surface and finish.
The product title identifies a stainless-steel cup holder with a blue LED, a combination that may suit buyers seeking an illuminated appearance at a recessed drink station. However, its specifications list plastic as the material, so the supplied information does not resolve the construction mismatch. Dimensions are listed as 4 by 4 by 2.5 inches, which offers an overall size reference but does not state a required cutout. Check the stated measurements against the planned mounting space before selecting it.
- Blue LED light identified in the product title
- Flush-mount cup holder format
- Title identifies stainless steel
- Listed dimensions are 4 by 4 by 2.5 inches
- Specifications list plastic material, conflicting with the stainless-steel title.
Skip it if you need a verified stainless-steel material specification; the Whitecap S-3511C explicitly lists stainless steel.
Consider this Whitecap if the blue LED is central to your drink-station choice and its listed dimensions suit the space. The title and material specification conflict, so buyers prioritizing confirmed construction should look elsewhere.
Full product details
| Brand | Whitecap |
|---|---|
| Color | No Color |
| Included Components | Great Product |
| Dimensions | 4"L x 4"W x 2.5"H |
| Item Weight | 5.6 ounces |
| Manufacturer | Tecnoseal |
| Part Number | S-3511BC |
| Manufacturer Warranty Description | Warranty |
| Material | Plastic |
| Model Number | CWR-56234 |
| Additional Information | Important Information Proposition 65 Warning for California Consumers WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov |
Listed on Amazon as: Whitecap S-3511BC Flush Mount Cup Holder W/Blue Led Light – Stainless Steel
View on Amazon
#9
9. BETIMFAN Stainless Drop-In Holder
- Dimensions: 4.13"L x 4.13"W x 3.43"H
- Material: Stainless Steel
Best for: Two-piece stainless set.
Why it ranks #9: The two-piece stainless set is intended for boats, RVs, and vehicles, but its description emphasizes drop-in placement rather than a specified flush cutout.
Two recessed holders made from 304 stainless steel give this set a durable material choice for multiple drink stations. Its drop-in installation is described for existing cup racks or table cutouts, while the listed applications span boats, RVs, vehicles, sofas, tables, theater seats, and other furniture.
The two-piece pack lets buyers outfit two locations or keep a matching pair in one setting, and 304 stainless steel supplies the specified construction material. Drop-in installation is described as placing each holder into an existing cup rack or table cutout, which can simplify use where a suitable opening already exists. The broad application list includes marine, vehicle, and indoor furniture settings. Product dimensions are 4.13 by 4.13 by 3.43 inches; the listing does not specify a cutout diameter.
- Pack includes two holders
- 304 stainless-steel construction
- Drop-in installation for existing racks or cutouts
- Listed for boats, RVs, vehicles, and furniture
- The listing does not specify a required cutout diameter.
Skip it if you need a published cutout measurement before making an opening; the Whitecap S-3511C specifies 3-7/8 inches.
This BETIMFAN set suits buyers needing two stainless recessed holders for boat, RV, vehicle, or furniture projects with existing openings. Its drop-in approach depends on a suitable cutout, whose diameter is not specified.
Full product details
| Brand | BETIMFAN |
|---|---|
| Color | Silver |
| Included Components | 2 x Drop in Cup Holder |
| Dimensions | 4.13"L x 4.13"W x 3.43"H |
| Manufacturer | BETIMFAN |
| Part Number | 205100tZ82uD0610400H101 |
| Manufacturer Warranty Description | no |
| Material | Stainless Steel |
| Model Number | 205100tZ82uD0610400H101 |
Listed on Amazon as: 2Pack Drop-in Cup Holder, 304 Stainless Steel Recessed Drink Holders
View on Amazon
#10
10. harayaa Flush Mount Insert
- Dimensions: 4.33"L x 4.33"W x 2.17"H
Best for: Glossy recessed panels.
Why it ranks #10: It is described as a recessed insert with a deep cavity, but the listing does not provide a mounting-hole diameter or interior cup dimensions.
A single rigid molded piece with a glossy, easy-to-clean surface gives this insert a simple recessed option for flat panels. Its deep cylindrical cavity is described as helping secure drinks during transit, while the wide outer flange and seamless panel profile keep the holder integrated rather than protruding into the surrounding space.
The one-piece rigid construction avoids a multi-part form, and the glossy surface is specifically described as easy to clean, supporting straightforward upkeep. Its recessed shape merges into flat panels without taking unnecessary space, while the wide outer flange provides a broad edge around the opening. The deep cylindrical cavity is intended to hold drinks securely and help prevent spills during transit. Listed dimensions are 4.33 by 4.33 by 2.17 inches; no cutout diameter is supplied.
- Single rigid molded piece
- Glossy surface described as easy to clean
- Recessed profile for flat panels
- Deep cylindrical cavity and wide outer flange
- The product listing does not provide a required cutout diameter.
Skip it if you need a specified cutout size before installation; the Whitecap S-3511C lists a 3-7/8-inch cutout.
This harayaa insert fits buyers seeking a glossy recessed holder for flat panels and a deep cavity for drinks during travel. Its 4.33-by-4.33-by-2.17-inch dimensions are listed, but the cutout diameter is not.
Full product details
| Brand | harayaa |
|---|---|
| Color | Black |
| Included Components | 1 black automotive cup holder |
| Dimensions | 4.33"L x 4.33"W x 2.17"H |
| Manufacturer | harayaa |
| Part Number | 3000413180930046203305 |
| Manufacturer Warranty Description | No warranty specified |
Listed on Amazon as: Flush Mount Cup Holder Insert
View on AmazonAvoid the cutout-size trap
A holder’s outside flange, inside opening, and required panel cutout are different measurements, so match the cutout specification to the hole you will make. The Sea-Dog 588000 requires a 3-inch hole and fits containers up to 2-7/8 inches in diameter; its small opening does not mean every larger cup will fit. The SDTC Tech Sofa Cup Holder specifies a 3.5-inch mounting hole and a 3.36-inch maximum beverage diameter.
The Whitecap S-3511C calls for a 3-7/8-inch cutout and lists a 4-1/4-inch outside diameter. Do not use an outside diameter as a substitute for the cutout size.
Some listings omit one or more of these measurements, including the harayaa insert and LED Whitecap listing. When dimensions are missing, confirm the precise hole and cup measurements with the seller or manufacturer before cutting a finished surface.
Plan drainage before mounting
A drain feature only helps if water has somewhere appropriate to go after it leaves the holder. The Whitecap S-3511C includes a drain tube, gasket, and pad, while the Sea-Dog 588060 and Amarine Made Recessed Holder list drain holes. The MARINE CITY Closeable Drain Holder takes a different approach: its drain can be closed and sealed with the supplied nut and bolt.
These are not interchangeable installation details. A drain tube needs a route and outlet; an open drain hole may let liquid pass through the panel; and a closable drain can retain liquid when sealed.
The product details do not specify how to route or seal every installation, so consider what is beneath your mounting surface and whether spilled liquid must be contained. For furniture or an enclosed panel, a through-drain could create a problem; for a suitable marine installation, drainage may be useful if the outlet is planned.
How to Choose a Flush-Mount Cup Holder
Cutout and cup diameter
Start by checking both the required panel opening and the maximum cup diameter the holder accepts. The Sea-Dog 588000 requires a 3-inch hole and accommodates containers up to 2-7/8 inches in diameter; the SDTC Tech Sofa Cup Holder calls for a 3.5-inch hole and fits beverages up to 3.36 inches. The Sea-Dog 588060 requires a 3-3/4-inch opening and has a 3-5/8-inch inside diameter.
These measurements are not the same as the outside flange diameter. Buyers replacing a small existing holder should favor the Sea-Dog 588000’s stated opening, while those regularly using wider cups or can coolers should compare the larger interiors and confirm their panel can take the cutout.
Depth and drinkware style
Choose depth and opening shape around the containers you actually use, rather than assuming one holder fits every can, bottle, or insulated cup. The Sea-Dog 588060 is 3-1/4 inches deep and specifically supports cans with or without insulated wraps. The Whitecap S-3511C has a stated depth range of 2-1/4 to 3-1/8 inches, and the SDTC Tech Sofa Cup Holder is 2.5 inches deep.
The Sea-Dog 588000 is offered in 2-inch or 3-inch depth versions, though this listing identifies the 2-inch model. A deeper holder may suit a mounting location where more container support is useful; a shallower one may suit a panel with limited clearance beneath it.
Check the underside space as well as the cup dimensions.
Material and drainage
Match the material and drain arrangement to the mounting environment and how you intend to handle spills. The Sea-Dog models use injection-molded ABS, the SDTC Tech holder is ABS, and the Whitecap S-3511C is stainless steel with a supplied gasket, pad, and drain tube. Plastic options include drain details such as the Sea-Dog 588060’s drain holes, the Amarine Made holder’s drain holes, and the MARINE CITY holder’s closable drain.
A stainless holder may appeal when you want a metal finish; a plastic model may better match a black panel or furniture. Buyers installing over a surface that must stay dry should pay particular attention to the drain path and whether it can be closed, rather than choosing by material alone.
Which Flush-Mount Cup Holder Should You Choose?
For a versatile marine-style holder that accommodates cans with or without insulated wraps, choose the Sea-Dog 588060 Combo Drink Holder; its listed 3-5/8-inch inside diameter and 3-3/4-inch hole requirement make the fit requirements clear. If you prefer stainless steel and want mounting and drainage parts included, the Whitecap S-3511C Stainless Drink Holder includes a gasket, pad, and drain tube. For a smaller specified opening, consider the Sea-Dog 588000 Flush Drink Holder, which requires a 3-inch hole but accepts containers only up to 2-7/8 inches wide.
For several mounting locations, the Amarine Made Recessed Holder comes as a three-piece set with drain holes. If you need a closable drain, the MARINE CITY Closeable Drain Holder specifies one.
Verify omitted cutout dimensions before committing to a panel.
Frequently Asked Questions
How do I measure a panel and cup to confirm a flush-mount holder will fit?
Measure the panel’s available flat area and thickness, then compare the required cutout and holder depth with the space behind it. Measure your cup or can at its widest point and compare it with the holder’s stated inside diameter or container limit. If a listing omits a dimension, verify it before cutting.
Do flush-mount cup holders need a drain, and where should the water go?
A drain is useful when liquid or wash water could collect, but the right setup depends on the location and holder. Route any drain to a suitable discharge point rather than into the panel or enclosed space. Check what the product includes: the Whitecap S-3511C lists a drain tube, while some holders have drain holes.
Can I install a flush-mount cup holder in a thin panel or curved surface?
Only if the holder’s mounting requirements suit the panel and the opening can be made on a stable, sufficiently flat area. Compare the holder depth with the space behind the panel, and check whether its rim can sit evenly. The supplied listings do not give every mounting dimension, so confirm omitted details first.
What should I check if I want a holder for insulated can wraps?
Check the listed inside diameter and whether the holder is described as accommodating a can with its wrap. The Sea-Dog 588060 is the stated choice for cans with or without insulated can wraps, with a 3-5/8-inch inside diameter. Confirm the cutout requirement too, since this holder requires a 3-3/4-inch hole.
Which option suits several mounting locations?
The Amarine Made recessed holder is listed as a set of three and has drain holes, making it the supplied option for multiple locations. Check each intended panel for adequate flat area and clearance behind it, and verify any cutout dimensions before installation because they are not provided in the product title.
Final Words
For a versatile marine-style fit that accommodates cans with or without insulated wraps, the Sea-Dog 588060 is the strongest overall pick, provided its 3-3/4-inch hole requirement suits your panel. Choose the Sea-Dog 588000 when a smaller, 3-inch opening matters and your containers are no wider than 2-7/8 inches. Prefer stainless steel with drainage parts included?
Consider the Whitecap S-3511C. Verify omitted dimensions before cutting.


